Exactly how to Replace a Bath Tub (Step By Step).
Exactly how to Replace a Bath Tub (Step By Step).
Blog Article
We've noticed this article involving How to Install a Bathtub below on the web and think it made sense to share it with you here.
Setting up a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, as well as often, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately tough job. If the old tub is easily available, the job can move quickly; if you need to open up a wall surface to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will need an assistant to leave the old bathtub and also set in the brand-new one. Ensure you have actually certified yourself for the task and fit attempting it. Instead of employing a service provider to take over a halfway-completed job, it is better to consider employing one before you start. Possibilities are you may need an expert plumber to make tube links.
This post will assist you mount a new bathtub in your restroom if you have actually currently purchased a new tub as well as don't need to transform the plan of your previous supply of water pipelines.
Your devices and material list must comprise the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water system. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of eliminating the existing faucets can be rather problematic because of the limited accessibility that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will originate from the pipes. When the supply pipes have been eliminated, use the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Before going on to fit the brand-new faucets, compare the pipe links on the old taps to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The previous kind ought to be attached to the tap finishes initially, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Utilizing both wooden boards under its feet, position the bath tub in the required setting. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the bathtub until the spirit level reviews degree.
To install taps, fit the bottom of the outermost adaptable faucet connector to the proper supply pipeline by making a compression sign up with; then do the same for the other faucet.
Activate the water supply and check all joints and new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
Finally, repair the bath paneling as explained in the maker's user's manual. Tiling as well as securing around the bath tub needs to wait till the bathtub has been used at least once as this will resolve it right into its last placement.
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to now prepare to be suited its final placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to crack a stiff seal, causing the water to permeate the wall surface between the bathroom as well as the tiling, bring about issues with wetness and feasible leaks to the ceiling below.
You can pick from a range of coloured sealers to blend in your components and fittings. They are marketed in tubes and cartridges, as well as are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the activity experienced when the tub remains in usage. The sealant can split rather early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is suggested to fit the tiles using water-resistant or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very fascinated with Tools You Need to Install a New Bathtub and I hope you liked my page. Sharing is nice. You never know, you will be doing someone a favor. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
Quote Report this page